PURATHANE

URETHANE COATINGS PURAMATE is water borne Wet Edge Extender developed for addition to PURATHANE and PURATHANE TWO PACK. Recommended for use when coating in hot conditions, especially large areas where it is difficult to maintain a ‘wet edge’.

 

PHYSICAL DESCRIPTION

Appearance:      Transparent liquid.
Colour:                Water clear.
PH:                        Approximately 7
Specific Gravity @ 25ºC: Approximately 1

 

SUITABLE FOR USE WITH

PURATHANE GLOSS
PURATHANE SATIN
PURATHANE MATT
PURATHANE TWO PACK GLOSS
PURATHANE TWO PACK SATIN
PURATHANE TWO PACK MATT

DIRECTIONS

Recommended for use when coating in hot conditions, especially large areas where it is difficult to maintain a ‘wet edge’.

ADDITION RATE

Initially add 50mls of PURAMATE per Litre of PURATHANE mixing thoroughly. Continue adding PURAMATE in increments of 20mls per Litre of PURATHANE up to 100mls per Litre of PURATHANE as necessary to slow drying, maintain flow, and assist self levelling.

IMPORTANT NOTICE

PURAMAX (anti rejection fluid) is compatible with PURAMATE and accordingly can be added simultaneously into PURATHANE however the addition of one or both should not exceed 100mls per Litre of PURATHANE.

CLEAN UP

Thoroughly wash brush, roller, applicator and equipment with water. Dry all equipment before reusing.

PACKAGING

URETHANE COATINGS PURAMATE is available in 1 Litre plastic bottles.

SHELF LIFE

URETHANE COATINGS PURAMATE is best if used within 24 months from manufacture (refer to batch number on label), when stored in unopened containers under normal conditions of temperature (between 5ºC and 30ºC – DO NOT FREEZE) and humidity. Keep containers closed when not in use.

RESPONSIBLE CARE

URETHANE COATINGS are proud of a conservative tradition of responsible care, and therefore regardless that the VOC levels of PURATHANE are low, it is inappropriate to advise PURATHANE (and all other water borne coatings) is non toxic. Accordingly URETHANE COATINGS recommend that personal protective equipment is used when applying this product.

SAFETY DIRECTIONS

For detailed Health and Safety information refer to the PURAMATE MSDS as it is an integral part of using this product.
PURAMATE is classified as Non-Hazardous however URETHANE COATINGS recommend usage of this material must be in well ventilated conditions to minimise inhalation of vapours. If applying in confined conditions wear respirator with filters that conform to AS 1716. Prevent skin contact by wearing appropriate protective clothing. May irritate skin and eyes. Keep containers firmly closed when not in use. In case of spillage absorb into dry sand or dirt then remove from work area and complete disposal in a responsible manner.

FIRST AID

If affected by inhalation of vapour, remove to fresh air. If breathing difficulty persists or occurs later consult a doctor and have MDSD ready. If swallowed, give water or milk to drink and Do Not induce vomiting. Contact a Doctor or Poisons Information Centre Australia 131126. In case of eye contact, ensuring eyelids are held open, flush immediately with water for fifteen minutes. In case of skin contact, remove contaminated clothing and wash skin with soap and water.

URETHANE COATINGS PURAMAX is water borne Anti Rejection Fluid developed for addition to PURATHANE and PURATHANE TWO PACK. Recommended for use when rejection occurs (coating pulling back to form ‘craters’ or ‘fisheyes’).

 

PHYSICAL DESCRIPTION

Appearance:      Opaque liquid.
Colour:                Slightly milky.
PH:                       Approximately 7
Specific Gravity @ 25ºC: Approximately 1

SUITABLE FOR USE WITH:

PURATHANE GLOSS
PURATHANE SATIN
PURATHANE MATT
PURATHANE TWO PACK GLOSS
PURATHANE TWO PACK SATIN
PURATHANE TWO PACK MATT

DIRECTIONS

Recommended for use when rejection occurs (coating pulling back to form ‘craters’ or ‘fisheyes’).

SURFACE PREPARATION

Dampen a rag or mop with Urethane Coatings THINNERS or CLEANING SOLVENT and wipe over the floor. Every 5m² rinse the rag or mop in clean THINNERS or CLEANING SOLVENT and re-dampen the rag or mop and continue wiping the floor, until the entire area of rejection is cleaned, thereby removing surface contaminants rather than further smearing contaminants over the floor.

ADDITION RATE

Initially add 20mls of PURAMAX per Litre of PURATHANE and mix thoroughly. Soon after application, inspect surface for rejection. Continue adding PURAMAX in increments of 20mls per Litre of PURATHANE until the surface is free from rejections or up to a maximum of 100mls per Litre of PURATHANE.

IMPORTANT NOTICE

PURAMATE (water borne Wet Edge Extender) is compatible with PURAMAX and accordingly can be added simultaneously into PURATHANE however the addition of one or both should not exceed 100mls per Litre of PURATHANE.

CLEAN UP

Thoroughly wash brush, roller, applicator and equipment with water. Dry all equipment before reusing.

PACKAGING

URETHANE COATINGS PURAMAX is available in 1 Litre plastic bottles.

SHELF LIFE

URETHANE COATINGS PURAMAX is best if used within 24 months from manufacture (refer to batch number on label), when stored in unopened containers under normal conditions of temperature (between 5ºC and 30ºC – DO NOT FREEZE) and humidity. Keep containers closed when not in use.

RESPONSIBLE CARE

URETHANE COATINGS are proud of a conservative tradition of responsible care, and therefore regardless that the VOC levels of PURATHANE are low, it is inappropriate to advise PURATHANE (and all other water borne coatings) is non toxic. Accordingly URETHANE COATINGS recommend that personal protective equipment is used when applying this product.

SAFETY DIRECTIONS

For detailed Health and Safety information refer to the PURAMAX MSDS as it is an integral part of using this product.
PURAMAX is classified as Non-Hazardous however URETHANE COATINGS recommend usage of this material must be in well ventilated conditions to minimise inhalation of vapours. If applying in confined conditions wear respirator with filters that conform to AS 1716. Prevent skin contact by wearing appropriate protective clothing. May irritate skin and eyes. Keep containers firmly closed when not in use. In case of spillage absorb into dry sand or dirt then remove from work area and complete disposal in a responsible manner.

FIRST AID

If affected by inhalation of vapour, remove to fresh air. If breathing difficulty persists or occurs later consult a doctor and have MDSD ready. If swallowed, give water or milk to drink and Do Not induce vomiting. Contact a Doctor or Poisons Information Centre Australia 131126. In case of eye contact, ensuring eyelids are held open, flush immediately with water for fifteen minutes. In case of skin contact, remove contaminated clothing and wash skin with soap and water.

URETHANE COATINGS PURASEAL is fast drying water borne sealer developed to seal your timber and parquetry floors and thereby ensure that the subsequent coat of PURATHANE remains on the surface to maximise the wear layer. PURASEAL retains the natural colour of timber and has a reduced sheen finish to assist in preventing ‘misses’ in the next coat.
Because water is used as the alternative carrier to solvent, URETHANE COATINGS PURASEAL emits low VOC’S (volatile organic compounds) and is therefore user and environmentally friendly but retains all the benefits, including the reduced risk of edge bonding, of solvent based sealer.

Physical Description

Appearance:        Opaque liquid.
Colour:                   Milky white.
PH:                          <7
Specific Gravity @ 25�C: >1.

 

FLOOR PREPARATION:

General:

1. Check that timber is adequately seasoned as if not, any subsequent cracking warping and shrinkage may compromise adhesion.
2. Ensure the surface is dry and thoroughly clean, removing all dirt, mildew, wax, grease, resin oils, tannins and dust.
3. Nail holes and surface defects should be filled with water based putty.

New Floors:

Follow steps 1 to 3 above, sand the floor and fine sand, finishing with 120 grit screen back or pad and vacuum thoroughly.

Old Floors:

Follow steps 2 to 3 above and clean with hot water and detergent. Roughen surface completely with 100 grit sandpaper and fine sand, finishing with 120 grit screen back or pad and vacuum thoroughly.

APPLICATION:

URETHANE COATINGS recommend a 3 coat system for most situations; 1st coat PURASEAL, followed by 2nd and 3rd coats of PURATHANE or PURATHANE TWO PACK. A 2 coat system will achieve a high performance finish on hardwood when applied at the rate of 8m² per Litre.

Application Orientation:

UV Stable, ideal for internal use, verandas, and covered patios.

Application Method: 3 Coat System

1st Coat. Decant PURASEAL directly from the container. Cut in edges with a paint edger or brush, taking care not to proceed excessively ahead of the main coating (particularly in hot and/or dry conditions). Apply PURASEAL at the rate of 10m² per Litre with a 10mm nap waterbased type roller cover or a waterbased applicator, disperse into a uniform finish taking care not to ‘overwork the coating’ allowing it to self level, and wherever possible, finish parallel with the grain. Allow 1.5 to 2 hours to dry (@ 25ºC and 50% R.H.) and prepare to recoat. Do not return unused material to the container.
It is not necessary to fine sand or buff PURASEAL unless surface imperfections or raised grain exist – if so allow 3 hours to dry and then buff with 150 grit screen back (or finer), taking extreme care not to cut through the PURASEAL as this will allow the next coat to ‘wet’ the timber which may dry a slightly different colour.

2nd Coat. Decant PURATHANE or PURATHANE TWO PACK directly from the container. Cut in edges with a paint edger or brush, taking care not to proceed excessively ahead of the main coating (particularly in hot and/or dry conditions). Apply PURATHANE or PURATHANE TWO PACK at the rate of 10m² per Litre with a 10mm nap waterbased type roller cover or a waterbased applicator, disperse into a uniform finish taking care not to ‘overwork the coating’ allowing it to self level, and finish wherever possible parallel with the grain. Allow 2 hours 30 minutes to dry (@ 25ºC and 50% R.H.) and buff with 150 grit screen back, vacuum thoroughly and prepare to recoat. Do not return unused material to the container.

3rd Coat. Repeat directions as detailed under 2nd Coat, finishing parallel with the grain. Allow 8 hours to dry (@ 25ºC and 50% R.H.) before providing access for light foot traffic.

Application Conditions:

Do not apply PURATHANE when ambient/surface temperature is below 10ºC or above 30ºC.
Do not apply PURATHANE if relative humidity is in excess of 85%.
Do not apply PURATHANE if the moisture content of timber is in excess of 14%.

 

USE and MAINTENANCE of a 3 COAT SYSTEM

PURATHANE and PURATHANE TWO PACK require 2-3 days (@ 25ºC and 50% R.H.) to cure before regular use, and 5 days before using cleaning formulations. Avoid heavy traffic during this period. After the curing period sweep regularly with a soft bristle broom, and if preferred rugs/mats/carpet squares can be placed on the floor. To clean your floor, mix up to one cup Methylated Spirit into a bucket of hot water, and mop the floor regularly rinsing the mop. Use protective pads under legs of furniture. Dirt and grit are abrasive when on the soles of shoes, and can damage any coating. Accordingly mats placed at entrances can assist in removal of grit, reducing abrasion and protecting the coating.

DRYING TIME:

Touch dry: 45 minutes. Through Dry: 2 hours. Recoat: 90 to 120 minutes (If Sanding is required allow 3 hours to dry.). All drying times are @ 25ºC and 50% relative humidity. Reduced temperature and/or increased humidity can delay drying time.

COVERAGE:

10m² per Litre.

THINNING:

URETHANE COATINGS PURASEAL does not require thinning. In hot and/or dry conditions and very large areas where it is difficult to maintain a wet edge, add 50ml of URETHANE COATINGS PURAMATE Wet Edge Extender per Litre of PURASEAL and refer to URETHANE COATINGS PURAMATE directions.

CLEAN UP:

Thoroughly wash brush, roller, applicator and equipment with water. If PURASEAL is allowed to ‘become tacky’ on equipment, first rinse off excess with water, then wash off any build up of PURATHANE with URETHANE COATINGS CLEANING SOLVENT or Methylated Spirit, then rinse with water. Dry all equipment before reusing.

PACKAGING:

URETHANE COATINGS PURASEAL is available in 5 and 10 Litre plastic bottles.

SHELF LIFE:

URETHANE COATINGS PURASEAL is best if used within 12 months from manufacture (refer to batch number on label), when stored in unopened containers under normal conditions of temperature (between 5ºC and 30ºC – DO NOT FREEZE) and humidity. Keep containers closed when not in use.

RESPONSIBLE CARE:

URETHANE COATINGS are proud of a conservative tradition of responsible care, and therefore regardless that the VOC levels of PURASEAL are low, it is inappropriate to advise PURASEAL (and all other water borne coatings) is non toxic. Accordingly URETHANE COATINGS recommend that personal protective equipment is used when applying this product.

SAFETY DIRECTIONS:

For detailed Health and Safety information refer to the PURASEAL MSDS as it is an integral part of using this product.
PURASEAL is classified as Non-Hazardous however URETHANE COATINGS recommend usage of this material must be in well ventilated conditions to minimise inhalation of vapours. If applying in confined conditions wear respirator with filters that conform to AS 1716. Prevent skin contact by wearing appropriate protective clothing. May irritate skin and eyes. Keep containers firmly closed when not in use. In case of spillage absorb into dry sand or dirt then remove from work area and complete disposal in a responsible manner.

FIRST AID:

If affected by inhalation of vapour, remove to fresh air. If breathing difficulty persists or occurs later consult a doctor and have MDSD ready. If swallowed, give water or milk to drink and Do Not induce vomiting. Contact a Doctor or Poisons Information Centre Australia 131126. In case of eye contact, ensuring eyelids are held open, flush immediately with water for fifteen minutes. In case of skin contact, remove contaminated clothing and wash skin with soap and water.

URETHANE COATINGS PURASHINE is water borne timber polish developed to provide your commercial timber and parquetry floors with extra protection particularly in very high traffic areas.
Because water is used as the carrier, URETHANE COATINGS PURASHINE GLOSS emits low VOC’S (volatile organic compounds) and is therefore user and environmentally friendly but retains all the durable and hard wearing benefits of traditional polishes.

 

PREPARATION:

1. Thoroughly clean the floor and allow to it completely dry.
2. Ensure the surface is dry and free of all dirt, mildew, wax, grease, resin oils, tannins and dust. For the removal of previous coats of PURASHINE (and other polishes) use PURASTRIP referring to the directions on the PURASTRIP Technical Data Sheet or Label.

New Floors:

Follow steps 1 to 2 above, and ensure the timber finish (Moisture Cure Polyurethane, Two Part Polyurethane, Modified Oil or Water Borne) is fully cured. Generally after the last coat of any system is applied, it requires a minimum of 7 days to cure (@ 25�C and 50% R.H.) and longer at reduced temperature and/or increased humidity.

Old Floors:

Follow steps 1 to 2 above.

APPLICATION:

URETHANE COATINGS recommend a 3 coat system for most situations. A 2 coat system will achieve a high performance finish on hardwood when applied at the rate of 40m² per Litre.

PURASHINE Preparation: Shake the container well for at least one minute and then stand the container for three minutes before using.

Application Orientation: UV Stable, ideal for internal use.

Application Method: 3 Coat System

1st Coat. Decant PURASHINE directly from the container. Cut in edges with a brush, taking care not to proceed excessively ahead of the main coating (particularly in hot and/or dry conditions). Apply PURASHINE at the rate of 50m² per Litre with a 10mm nap waterbased type roller cover or a waterbased applicator, disperse into a uniform finish taking care not to ‘overwork the coating’ allowing it to self level, and wherever possible, finish parallel with the grain. Allow 2 hours 30 minutes to dry (@ 25ºC and 50% R.H.) and prepare to recoat. Do not return unused material to the container.

2nd Coat. Repeat directions as detailed under 1st Coat, finishing parallel with the grain.

3rd Coat. Repeat directions as detailed under 2nd Coat, finishing parallel with the grain.
Allow 4 hours to dry (@ 25ºC and 50% R.H.) before providing access for light foot traffic.

Application CONDITIONS:

Do not apply PURASHINE when ambient/surface temperature is below 10ºC or above 30ºC.
Do not apply PURASHINE if relative humidity is in excess of 85%.
Do not apply PURASHINE if the moisture content of timber is in excess of 14%.

USE and MAINTENANCE

PURASHINE GLOSS requires 12 Hours (@ 25ºC and 50% R.H.) to cure before regular use, and 3 days before using cleaning formulations. Avoid heavy traffic during this period. After the curing period sweep regularly with a soft bristle broom, and if preferred rugs/mats/carpet squares can be placed on the floor. To clean your floor, mix up to one cup Methylated Spirit into a bucket of hot water, and mop the floor regularly rinsing the mop. Use protective pads under legs of furniture. Dirt and grit are abrasive when on the soles of shoes, and can damage any coating. Accordingly mats placed at entrances can assist in removal of grit, reducing abrasion and protecting the coating.

DRYING TIME

Touch dry: 30 minutes. Through Dry: 2 hours. Recoat: 2 hours 30 minutes. All drying times are @ 25ºC and 50% relative humidity. Reduced temperature and/or increased humidity can delay drying time.

COVERAGE:

50m² per Litre.

THINNING

URETHANE COATINGS PURASHINE does not require thinning. In hot and/or dry conditions and very large areas where it is difficult to maintain a wet edge, add 50ml of URETHANE COATINGS PURAMATE Wet Edge Extender per Litre of PURASHINE and refer to URETHANE COATINGS PURAMATE directions.

CLEAN UP

Thoroughly wash brush, roller, applicator and equipment with water. If PURASHINE is allowed to ‘become tacky’ on equipment, first rinse off excess with water, then wash off any build up of PURASHINE with URETHANE COATINGS CLEANING SOLVENT or Methylated Spirit, then rinse with water. Dry all equipment before reusing.

PACKAGING

URETHANE COATINGS PURASHINE is available in 5 Litre plastic bottles.

SHELF LIFE

URETHANE COATINGS PURASHINE is best if used within 12 months from manufacture (refer to batch number on label), when stored in unopened containers under normal conditions of temperature (between 5ºC and 30ºC – DO NOT FREEZE) and humidity. Keep containers closed when not in use.

RESPONSIBLE CARE

URETHANE COATINGS are proud of a conservative tradition of responsible care, and therefore regardless that the VOC levels of PURSHINE are low, it is inappropriate to advise PURASHINE (and all other water borne coatings) is non toxic. Accordingly URETHANE COATINGS recommend that personal protective equipment is used when applying this product.

SAFETY DIRECTIONS

For detailed Health and Safety information refer to the PURASHINE MSDS as it is an integral part of using this product.
PURASHINE is classified as Non-Hazardous however URETHANE COATINGS recommend usage of this material must be in well ventilated conditions to minimise inhalation of vapours. If applying in confined conditions wear respirator with filters that conform to AS 1716. Prevent skin contact by wearing appropriate protective clothing. May irritate skin and eyes. Keep containers firmly closed when not in use. In case of spillage absorb into dry sand or dirt then remove from work area and complete disposal in a responsible manner.

FIRST AID

If affected by inhalation of vapour, remove to fresh air. If breathing difficulty persists or occurs later consult a doctor and have MSDS ready. If swallowed, give water or milk to drink and Do Not induce vomiting. Contact a Doctor or Poisons Information Centre Australia 131126. In case of eye contact, ensuring eyelids are held open, flush immediately with water for fifteen minutes. In case of skin contact, remove contaminated clothing and wash skin with soap and water.

URETHANE COATINGS PURASHINE is water borne timber polish developed to provide your commercial timber and parquetry floors with extra protection particularly in very high traffic areas.
Because water is used as the carrier, URETHANE COATINGS PURASHINE SATIN emits low VOC’S (volatile organic compounds) and is therefore user and environmentally friendly but retains all the durable and hard wearing benefits of traditional polishes.

 

PREPARATION:

1. Thoroughly clean the floor and allow to it completely dry.
2. Ensure the surface is dry and free of all dirt, mildew, wax, grease, resin oils, tannins and dust. For the removal of previous coats of PURASHINE (and other polishes) use PURASTRIP referring to the directions on the PURASTRIP Technical Data Sheet or Label.

New Floors:

Follow steps 1 to 2 above, and ensure the timber finish (Moisture Cure Polyurethane, Two Part Polyurethane, Modified Oil or Water Borne) is fully cured. Generally after the last coat of any system is applied, it requires a minimum of 7 days to cure (@ 25�C and 50% R.H.) and longer at reduced temperature and/or increased humidity.

Old Floors:

Follow steps 1 to 2 above.

APPLICATION:

URETHANE COATINGS recommend a 3 coat system for most situations. A 2 coat system will achieve a high performance finish on hardwood when applied at the rate of 40m² per Litre.

PURASHINE Preparation: Shake the container well for at least one minute and then stand the container for three minutes before using.

Application Orientation: UV Stable, ideal for internal use.

Application Method: 3 Coat System

1st Coat. Decant PURASHINE directly from the container. Cut in edges with a brush, taking care not to proceed excessively ahead of the main coating (particularly in hot and/or dry conditions). Apply PURASHINE at the rate of 50m² per Litre with a 10mm nap waterbased type roller cover or a waterbased applicator, disperse into a uniform finish taking care not to ‘overwork the coating’ allowing it to self level, and wherever possible, finish parallel with the grain. Allow 2 hours 30 minutes to dry (@ 25ºC and 50% R.H.) and prepare to recoat. Do not return unused material to the container.

2nd Coat. Repeat directions as detailed under 1st Coat, finishing parallel with the grain.

3rd Coat. Repeat directions as detailed under 2nd Coat, finishing parallel with the grain.
Allow 4 hours to dry (@ 25ºC and 50% R.H.) before providing access for light foot traffic.

Application CONDITIONS:

Do not apply PURASHINE when ambient/surface temperature is below 10ºC or above 30ºC.
Do not apply PURASHINE if relative humidity is in excess of 85%.
Do not apply PURASHINE if the moisture content of timber is in excess of 14%.

USE and MAINTENANCE

PURASHINE GLOSS requires 12 Hours (@ 25ºC and 50% R.H.) to cure before regular use, and 3 days before using cleaning formulations. Avoid heavy traffic during this period. After the curing period sweep regularly with a soft bristle broom, and if preferred rugs/mats/carpet squares can be placed on the floor. To clean your floor, mix up to one cup Methylated Spirit into a bucket of hot water, and mop the floor regularly rinsing the mop. Use protective pads under legs of furniture. Dirt and grit are abrasive when on the soles of shoes, and can damage any coating. Accordingly mats placed at entrances can assist in removal of grit, reducing abrasion and protecting the coating.

DRYING TIME

Touch dry: 30 minutes. Through Dry: 2 hours. Recoat: 2 hours 30 minutes. All drying times are @ 25ºC and 50% relative humidity. Reduced temperature and/or increased humidity can delay drying time.

COVERAGE:

50m² per Litre.

THINNING

URETHANE COATINGS PURASHINE does not require thinning. In hot and/or dry conditions and very large areas where it is difficult to maintain a wet edge, add 50ml of URETHANE COATINGS PURAMATE Wet Edge Extender per Litre of PURASHINE and refer to URETHANE COATINGS PURAMATE directions.

CLEAN UP

Thoroughly wash brush, roller, applicator and equipment with water. If PURASHINE is allowed to ‘become tacky’ on equipment, first rinse off excess with water, then wash off any build up of PURASHINE with URETHANE COATINGS CLEANING SOLVENT or Methylated Spirit, then rinse with water. Dry all equipment before reusing.

PACKAGING

URETHANE COATINGS PURASHINE is available in 5 Litre plastic bottles.

SHELF LIFE

URETHANE COATINGS PURASHINE is best if used within 12 months from manufacture (refer to batch number on label), when stored in unopened containers under normal conditions of temperature (between 5ºC and 30ºC – DO NOT FREEZE) and humidity. Keep containers closed when not in use.

RESPONSIBLE CARE

URETHANE COATINGS are proud of a conservative tradition of responsible care, and therefore regardless that the VOC levels of PURSHINE are low, it is inappropriate to advise PURASHINE (and all other water borne coatings) is non toxic. Accordingly URETHANE COATINGS recommend that personal protective equipment is used when applying this product.

SAFETY DIRECTIONS

For detailed Health and Safety information refer to the PURASHINE MSDS as it is an integral part of using this product.
PURASHINE is classified as Non-Hazardous however URETHANE COATINGS recommend usage of this material must be in well ventilated conditions to minimise inhalation of vapours. If applying in confined conditions wear respirator with filters that conform to AS 1716. Prevent skin contact by wearing appropriate protective clothing. May irritate skin and eyes. Keep containers firmly closed when not in use. In case of spillage absorb into dry sand or dirt then remove from work area and complete disposal in a responsible manner.

FIRST AID

If affected by inhalation of vapour, remove to fresh air. If breathing difficulty persists or occurs later consult a doctor and have MSDS ready. If swallowed, give water or milk to drink and Do Not induce vomiting. Contact a Doctor or Poisons Information Centre Australia 131126. In case of eye contact, ensuring eyelids are held open, flush immediately with water for fifteen minutes. In case of skin contact, remove contaminated clothing and wash skin with soap and water.

WATCH THIS SPACE – COMING SOON!

URETHANE COATINGS PURATHANE GLOSS is water borne polyurethane finish developed to provide your timber and parquetry floors with extremely hardwearing and long lasting protection.

Because water is used as the alternative carrier to solvent, URETHANE COATINGS PURATHANE GLOSS emits low VOC’S (volatile organic compounds) and is therefore user and environmentally friendly but retains all the durable and hard wearing benefits of solvent based polyurethane.

PHYSICAL DESCRIPTION

Appearance:           Opaque liquid.
Colour:                      Milky white.
PH:                             >7
Specific Gravity @ 25�C:   >1.

 

FLOOR PREPARATION

General:

1. Check that timber is adequately seasoned as if not, any subsequent cracking warping and shrinkage may compromise adhesion.
2. Ensure the surface is dry and thoroughly clean, removing all dirt, mildew, wax, grease, resin oils, tannins and dust.
3. Nail holes and surface defects should be filled with water based putty.

New Floors:

Follow steps 1 to 3 above, sand the floor and fine sand, finishing with 120 grit screen back or pad and vacuum thoroughly.

Old Floors:

Follow steps 2 to 3 above and clean with hot water and detergent. Roughen surface completely with 100 grit sandpaper and fine sand, finishing with 120 grit screen back or pad and vacuum thoroughly.
If there is risk of contamination, test for compatibility by applying PURATHANE on a small section of floor first. If ‘craters’ or ‘fisheyes’ appear add 20mls of URETHANE COATINGS PURAMAX Anti Rejection Fluid per Litre of PURATHANE and refer to URETHANE COATINGS PURAMAX directions.

APPLICATION:

URETHANE COATINGS recommend a 3 coat system for most situations; 1st coat PURASEAL, followed by 2nd and 3rd coats of PURATHANE. A 2 coat system will achieve a high performance finish on hardwood when applied at the rate of 8m² per Litre.

PURATHANE Preparation

Shake the container well for at least one minute and then stand the container for three minutes before using.
Coat PURASEAL with either PURATHANE or PURATHANE TWO PACK.
N.B. (1) PURATHANE GLOSS, SATIN and MATT are completely compatible with each other, and can be mixed together and coated over each other. (2) PURATHANE TWO PACK GLOSS, SATIN and MATT are completely compatible with each other, and also can be mixed together and coated over each other. (3) Do not mix PURASEAL with PURATHANE or PURATHANE TWO PACK.

As an alternative to PURASEAL, URETHANE COATINGS solvent based TIMBERSEAL is a well proven fast drying sealer. As a 3 coat system TIMBERSEAL can be coated with PURATHANE or PURATHANE TWO PACK.

Application Orientation

UV Stable, ideal for internal use, verandas, and covered patios.

Application Method: 3 Coat System

1st Coat. Decant PURASEAL directly from the container. Cut in edges with a paint edger or brush, taking care not to proceed excessively ahead of the main coating (particularly in hot and/or dry conditions). Apply PURASEAL at the rate of 10m² per Litre with a 10mm nap waterbased type roller cover or a waterbased applicator, disperse into a uniform finish taking care not to ‘overwork the coating’ allowing it to self level, and wherever possible, finish parallel with the grain. Allow 1.5 to 2 hours to dry (@ 25ºC and 50% R.H.) and prepare to recoat. Do not return unused material to the container.
It is not necessary to fine sand or buff PURASEAL unless surface imperfections or raised grain exist – if so allow 3 hours to dry and then buff with 150 grit screen back (or finer), taking extreme care not to cut through the PURASEAL as this will allow the next coat to ‘wet’ the timber which may dry a slightly different colour.

2nd Coat. Decant PURATHANE directly from the container. Cut in edges with a paint edger or brush, taking care not to proceed excessively ahead of the main coating (particularly in hot and/or dry conditions). Apply PURATHANE at the rate of 10m² per Litre with a 10mm nap waterbased type roller cover or a waterbased applicator, disperse into a uniform finish taking care not to ‘overwork the coating’ allowing it to self level, and finish wherever possible parallel with the grain. Allow 2 hours 30 minutes to dry (@ 25ºC and 50% R.H.) and buff with 150 grit screen back, vacuum thoroughly and prepare to recoat. Do not return unused material to the container.

3rd Coat. Repeat directions as detailed under 2nd Coat, finishing parallel with the grain. Allow 8 hours to dry (@ 25ºC and 50% R.H.) before providing access for light foot traffic.

Application Conditions

Do not apply PURATHANE when ambient/surface temperature is below 10ºC or above 30ºC.
Do not apply PURATHANE if relative humidity is in excess of 85%.
Do not apply PURATHANE if the moisture content of timber is in excess of 14%.

Sanding

PURATHANE is suitable for sanding after 2hours 30 minutes drying (@ 25ºC and 50% R.H.). A good indication that PURTHANE is sufficiently dry is when light sanding using a 150 grit screen back or buffing pad, produces a fine white powder.

USE and MAINTENANCE of a 3 COAT SYSTEM

PURATHANE GLOSS requires 2-3 days (@ 25ºC and 50% R.H.) to cure before regular use, and 5 days before using cleaning formulations. Avoid heavy traffic during this period. After the curing period sweep regularly with a soft bristle broom, and if preferred rugs/mats/carpet squares can be placed on the floor. To clean your floor, mix up to one cup Methylated Spirit into a bucket of hot water, and mop the floor regularly rinsing the mop. Use protective pads under legs of furniture. Dirt and grit are abrasive when on the soles of shoes, and can damage any coating. Accordingly mats placed at entrances can assist in removal of grit, reducing abrasion and protecting the coating.

DRYING TIME

Touch dry: 30 minutes.   Through Dry: 2 hours.   Sanding & Recoat: 2 hours 30 minutes (Without sanding recoat in 90 to 120 minutes). All drying times are @ 25ºC and 50% relative humidity. Reduced temperature and/or increased humidity can delay drying time.

COVERAGE

10m² per Litre.

THINNING

URETHANE COATINGS PURATHANE does not require thinning. In hot and/or dry conditions and very large areas where it is difficult to maintain a wet edge, add 50ml of URETHANE COATINGS PURAMATE Wet Edge Extender per Litre of PURATHANE and refer to URETHANE COATINGS PURAMATE directions.

CLEAN UP

Thoroughly wash brush, roller, applicator and equipment with water. If PURATHANE is allowed to ‘become tacky’ on equipment, first rinse off excess with water, then wash off any build up of PURATHANE with URETHANE COATINGS CLEANING SOLVENT or Methylated Spirit, then rinse with water. Dry all equipment before reusing.

PACKAGING

URETHANE COATINGS PURATHANE is available in 5 and 10 Litre plastic bottles.

SHELF LIFE

URETHANE COATINGS PURATHANE is best if used within 12 months from manufacture (refer to batch number on label), when stored in unopened containers under normal conditions of temperature (between 5ºC and 30ºC – DO NOT FREEZE) and humidity. Keep containers closed when not in use.

RESPONSIBLE CARE

URETHANE COATINGS are proud of a conservative tradition of responsible care, and therefore regardless that the VOC levels of PURATHANE are low, it is inappropriate to advise PURATHANE (and all other water borne coatings) is non toxic. Accordingly URETHANE COATINGS recommend that personal protective equipment is used when applying this product.

SAFETY DIRECTIONS

For detailed Health and Safety information refer to the PURATHANE MSDS as it is an integral part of using this product.
PURATHANE is classified as Non-Hazardous however URETHANE COATINGS recommend usage of this material must be in well ventilated conditions to minimise inhalation of vapours. If applying in confined conditions wear respirator with filters that conform to AS 1716. Prevent skin contact by wearing appropriate protective clothing. May irritate skin and eyes. Keep containers firmly closed when not in use. In case of spillage absorb into dry sand or dirt then remove from work area and complete disposal in a responsible manner.

FIRST AID

If affected by inhalation of vapour, remove to fresh air. If breathing difficulty persists or occurs later consult a doctor and have MDSD ready. If swallowed, give water or milk to drink and Do Not induce vomiting. Contact a Doctor or Poisons Information Centre Australia 131126. In case of eye contact, ensuring eyelids are held open, flush immediately with water for fifteen minutes. In case of skin contact, remove contaminated clothing and wash skin with soap and water.

URETHANE COATINGS PURATHANE MATT in is water borne polyurethane finish developed to provide your timber and parquetry floors with extremely hardwearing and long lasting protection.

Because water is used as the alternative carrier to solvent, URETHANE COATINGS PURATHANE MATT emits low VOC’S (volatile organic compounds) and is therefore user and environmentally friendly but retains all the durable and hard wearing benefits of solvent based polyurethane.

PHYSICAL DESCRIPTION

Appearance:           Opaque liquid.
Colour:                      Milky white.
PH:                             >7
Specific Gravity @ 25�C:   >1.

 

FLOOR PREPARATION

General:

1. Check that timber is adequately seasoned as if not, any subsequent cracking warping and shrinkage may compromise adhesion.
2. Ensure the surface is dry and thoroughly clean, removing all dirt, mildew, wax, grease, resin oils, tannins and dust.
3. Nail holes and surface defects should be filled with water based putty.

New Floors:

Follow steps 1 to 3 above, sand the floor and fine sand, finishing with 120 grit screen back or pad and vacuum thoroughly.

Old Floors:

Follow steps 2 to 3 above and clean with hot water and detergent. Roughen surface completely with 100 grit sandpaper and fine sand, finishing with 120 grit screen back or pad and vacuum thoroughly.
If there is risk of contamination, test for compatibility by applying PURATHANE on a small section of floor first. If ‘craters’ or ‘fisheyes’ appear add 20mls of URETHANE COATINGS PURAMAX Anti Rejection Fluid per Litre of PURATHANE and refer to URETHANE COATINGS PURAMAX directions.

APPLICATION:

URETHANE COATINGS recommend a 3 coat system for most situations; 1st coat PURASEAL, followed by 2nd and 3rd coats of PURATHANE. A 2 coat system will achieve a high performance finish on hardwood when applied at the rate of 8m² per Litre.

PURATHANE Preparation

Shake the container well for at least one minute and then stand the container for three minutes before using.
Coat PURASEAL with either PURATHANE or PURATHANE TWO PACK.
N.B. (1) PURATHANE GLOSS, SATIN and MATT are completely compatible with each other, and can be mixed together and coated over each other. (2) PURATHANE TWO PACK GLOSS, SATIN and MATT are completely compatible with each other, and also can be mixed together and coated over each other. (3) Do not mix PURASEAL with PURATHANE or PURATHANE TWO PACK.

As an alternative to PURASEAL, URETHANE COATINGS solvent based TIMBERSEAL is a well proven fast drying sealer. As a 3 coat system TIMBERSEAL can be coated with PURATHANE or PURATHANE TWO PACK.

Application Orientation

UV Stable, ideal for internal use, verandas, and covered patios.

Application Method: 3 Coat System

1st Coat. Decant PURASEAL directly from the container. Cut in edges with a paint edger or brush, taking care not to proceed excessively ahead of the main coating (particularly in hot and/or dry conditions). Apply PURASEAL at the rate of 10m² per Litre with a 10mm nap waterbased type roller cover or a waterbased applicator, disperse into a uniform finish taking care not to ‘overwork the coating’ allowing it to self level, and wherever possible, finish parallel with the grain. Allow 1.5 to 2 hours to dry (@ 25ºC and 50% R.H.) and prepare to recoat. Do not return unused material to the container.
It is not necessary to fine sand or buff PURASEAL unless surface imperfections or raised grain exist – if so allow 3 hours to dry and then buff with 150 grit screen back (or finer), taking extreme care not to cut through the PURASEAL as this will allow the next coat to ‘wet’ the timber which may dry a slightly different colour.

2nd Coat. Decant PURATHANE directly from the container. Cut in edges with a paint edger or brush, taking care not to proceed excessively ahead of the main coating (particularly in hot and/or dry conditions). Apply PURATHANE at the rate of 10m² per Litre with a 10mm nap waterbased type roller cover or a waterbased applicator, disperse into a uniform finish taking care not to ‘overwork the coating’ allowing it to self level, and finish wherever possible parallel with the grain. Allow 2 hours 30 minutes to dry (@ 25ºC and 50% R.H.) and buff with 150 grit screen back, vacuum thoroughly and prepare to recoat. Do not return unused material to the container.

3rd Coat. Repeat directions as detailed under 2nd Coat, finishing parallel with the grain. Allow 8 hours to dry (@ 25ºC and 50% R.H.) before providing access for light foot traffic.

Application Conditions

Do not apply PURATHANE when ambient/surface temperature is below 10ºC or above 30ºC.
Do not apply PURATHANE if relative humidity is in excess of 85%.
Do not apply PURATHANE if the moisture content of timber is in excess of 14%.

Sanding

PURATHANE is suitable for sanding after 2hours 30 minutes drying (@ 25ºC and 50% R.H.). A good indication that PURTHANE is sufficiently dry is when light sanding using a 150 grit screen back or buffing pad, produces a fine white powder.

USE and MAINTENANCE of a 3 COAT SYSTEM

PURATHANE GLOSS requires 2-3 days (@ 25ºC and 50% R.H.) to cure before regular use, and 5 days before using cleaning formulations. Avoid heavy traffic during this period. After the curing period sweep regularly with a soft bristle broom, and if preferred rugs/mats/carpet squares can be placed on the floor. To clean your floor, mix up to one cup Methylated Spirit into a bucket of hot water, and mop the floor regularly rinsing the mop. Use protective pads under legs of furniture. Dirt and grit are abrasive when on the soles of shoes, and can damage any coating. Accordingly mats placed at entrances can assist in removal of grit, reducing abrasion and protecting the coating.

DRYING TIME

Touch dry: 30 minutes.   Through Dry: 2 hours.   Sanding & Recoat: 2 hours 30 minutes (Without sanding recoat in 90 to 120 minutes). All drying times are @ 25ºC and 50% relative humidity. Reduced temperature and/or increased humidity can delay drying time.

COVERAGE

10m² per Litre.

THINNING

URETHANE COATINGS PURATHANE does not require thinning. In hot and/or dry conditions and very large areas where it is difficult to maintain a wet edge, add 50ml of URETHANE COATINGS PURAMATE Wet Edge Extender per Litre of PURATHANE and refer to URETHANE COATINGS PURAMATE directions.

CLEAN UP

Thoroughly wash brush, roller, applicator and equipment with water. If PURATHANE is allowed to ‘become tacky’ on equipment, first rinse off excess with water, then wash off any build up of PURATHANE with URETHANE COATINGS CLEANING SOLVENT or Methylated Spirit, then rinse with water. Dry all equipment before reusing.

PACKAGING

URETHANE COATINGS PURATHANE is available in 5 and 10 Litre plastic bottles.

SHELF LIFE

URETHANE COATINGS PURATHANE is best if used within 12 months from manufacture (refer to batch number on label), when stored in unopened containers under normal conditions of temperature (between 5ºC and 30ºC – DO NOT FREEZE) and humidity. Keep containers closed when not in use.

RESPONSIBLE CARE

URETHANE COATINGS are proud of a conservative tradition of responsible care, and therefore regardless that the VOC levels of PURATHANE are low, it is inappropriate to advise PURATHANE (and all other water borne coatings) is non toxic. Accordingly URETHANE COATINGS recommend that personal protective equipment is used when applying this product.

SAFETY DIRECTIONS

For detailed Health and Safety information refer to the PURATHANE MSDS as it is an integral part of using this product.
PURATHANE is classified as Non-Hazardous however URETHANE COATINGS recommend usage of this material must be in well ventilated conditions to minimise inhalation of vapours. If applying in confined conditions wear respirator with filters that conform to AS 1716. Prevent skin contact by wearing appropriate protective clothing. May irritate skin and eyes. Keep containers firmly closed when not in use. In case of spillage absorb into dry sand or dirt then remove from work area and complete disposal in a responsible manner.

FIRST AID

If affected by inhalation of vapour, remove to fresh air. If breathing difficulty persists or occurs later consult a doctor and have MDSD ready. If swallowed, give water or milk to drink and Do Not induce vomiting. Contact a Doctor or Poisons Information Centre Australia 131126. In case of eye contact, ensuring eyelids are held open, flush immediately with water for fifteen minutes. In case of skin contact, remove contaminated clothing and wash skin with soap and water.

URETHANE COATINGS PURATHANE SATIN in is water borne polyurethane finish developed to provide your timber and parquetry floors with extremely hardwearing and long lasting protection.

Because water is used as the alternative carrier to solvent, URETHANE COATINGS PURATHANE SATIN emits low VOC’S (volatile organic compounds) and is therefore user and environmentally friendly but retains all the durable and hard wearing benefits of solvent based polyurethane.

PHYSICAL DESCRIPTION

Appearance:           Opaque liquid.
Colour:                      Milky white.
PH:                             >7
Specific Gravity @ 25�C:   >1.

 

FLOOR PREPARATION

General:

1. Check that timber is adequately seasoned as if not, any subsequent cracking warping and shrinkage may compromise adhesion.
2. Ensure the surface is dry and thoroughly clean, removing all dirt, mildew, wax, grease, resin oils, tannins and dust.
3. Nail holes and surface defects should be filled with water based putty.

New Floors:

Follow steps 1 to 3 above, sand the floor and fine sand, finishing with 120 grit screen back or pad and vacuum thoroughly.

Old Floors:

Follow steps 2 to 3 above and clean with hot water and detergent. Roughen surface completely with 100 grit sandpaper and fine sand, finishing with 120 grit screen back or pad and vacuum thoroughly.
If there is risk of contamination, test for compatibility by applying PURATHANE on a small section of floor first. If ‘craters’ or ‘fisheyes’ appear add 20mls of URETHANE COATINGS PURAMAX Anti Rejection Fluid per Litre of PURATHANE and refer to URETHANE COATINGS PURAMAX directions.

APPLICATION:

URETHANE COATINGS recommend a 3 coat system for most situations; 1st coat PURASEAL, followed by 2nd and 3rd coats of PURATHANE. A 2 coat system will achieve a high performance finish on hardwood when applied at the rate of 8m² per Litre.

PURATHANE Preparation

Shake the container well for at least one minute and then stand the container for three minutes before using.
Coat PURASEAL with either PURATHANE or PURATHANE TWO PACK.
N.B. (1) PURATHANE GLOSS, SATIN and MATT are completely compatible with each other, and can be mixed together and coated over each other. (2) PURATHANE TWO PACK GLOSS, SATIN and MATT are completely compatible with each other, and also can be mixed together and coated over each other. (3) Do not mix PURASEAL with PURATHANE or PURATHANE TWO PACK.

As an alternative to PURASEAL, URETHANE COATINGS solvent based TIMBERSEAL is a well proven fast drying sealer. As a 3 coat system TIMBERSEAL can be coated with PURATHANE or PURATHANE TWO PACK.

Application Orientation

UV Stable, ideal for internal use, verandas, and covered patios.

Application Method: 3 Coat System

1st Coat. Decant PURASEAL directly from the container. Cut in edges with a paint edger or brush, taking care not to proceed excessively ahead of the main coating (particularly in hot and/or dry conditions). Apply PURASEAL at the rate of 10m² per Litre with a 10mm nap waterbased type roller cover or a waterbased applicator, disperse into a uniform finish taking care not to ‘overwork the coating’ allowing it to self level, and wherever possible, finish parallel with the grain. Allow 1.5 to 2 hours to dry (@ 25ºC and 50% R.H.) and prepare to recoat. Do not return unused material to the container.
It is not necessary to fine sand or buff PURASEAL unless surface imperfections or raised grain exist – if so allow 3 hours to dry and then buff with 150 grit screen back (or finer), taking extreme care not to cut through the PURASEAL as this will allow the next coat to ‘wet’ the timber which may dry a slightly different colour.

2nd Coat. Decant PURATHANE directly from the container. Cut in edges with a paint edger or brush, taking care not to proceed excessively ahead of the main coating (particularly in hot and/or dry conditions). Apply PURATHANE at the rate of 10m² per Litre with a 10mm nap waterbased type roller cover or a waterbased applicator, disperse into a uniform finish taking care not to ‘overwork the coating’ allowing it to self level, and finish wherever possible parallel with the grain. Allow 2 hours 30 minutes to dry (@ 25ºC and 50% R.H.) and buff with 150 grit screen back, vacuum thoroughly and prepare to recoat. Do not return unused material to the container.

3rd Coat. Repeat directions as detailed under 2nd Coat, finishing parallel with the grain. Allow 8 hours to dry (@ 25ºC and 50% R.H.) before providing access for light foot traffic.

Application Conditions

Do not apply PURATHANE when ambient/surface temperature is below 10ºC or above 30ºC.
Do not apply PURATHANE if relative humidity is in excess of 85%.
Do not apply PURATHANE if the moisture content of timber is in excess of 14%.

Sanding

PURATHANE is suitable for sanding after 2hours 30 minutes drying (@ 25ºC and 50% R.H.). A good indication that PURTHANE is sufficiently dry is when light sanding using a 150 grit screen back or buffing pad, produces a fine white powder.

USE and MAINTENANCE of a 3 COAT SYSTEM

PURATHANE GLOSS requires 2-3 days (@ 25ºC and 50% R.H.) to cure before regular use, and 5 days before using cleaning formulations. Avoid heavy traffic during this period. After the curing period sweep regularly with a soft bristle broom, and if preferred rugs/mats/carpet squares can be placed on the floor. To clean your floor, mix up to one cup Methylated Spirit into a bucket of hot water, and mop the floor regularly rinsing the mop. Use protective pads under legs of furniture. Dirt and grit are abrasive when on the soles of shoes, and can damage any coating. Accordingly mats placed at entrances can assist in removal of grit, reducing abrasion and protecting the coating.

DRYING TIME

Touch dry: 30 minutes.   Through Dry: 2 hours.   Sanding & Recoat: 2 hours 30 minutes (Without sanding recoat in 90 to 120 minutes). All drying times are @ 25ºC and 50% relative humidity. Reduced temperature and/or increased humidity can delay drying time.

COVERAGE

10m² per Litre.

THINNING

URETHANE COATINGS PURATHANE does not require thinning. In hot and/or dry conditions and very large areas where it is difficult to maintain a wet edge, add 50ml of URETHANE COATINGS PURAMATE Wet Edge Extender per Litre of PURATHANE and refer to URETHANE COATINGS PURAMATE directions.

CLEAN UP

Thoroughly wash brush, roller, applicator and equipment with water. If PURATHANE is allowed to ‘become tacky’ on equipment, first rinse off excess with water, then wash off any build up of PURATHANE with URETHANE COATINGS CLEANING SOLVENT or Methylated Spirit, then rinse with water. Dry all equipment before reusing.

PACKAGING

URETHANE COATINGS PURATHANE is available in 5 and 10 Litre plastic bottles.

SHELF LIFE

URETHANE COATINGS PURATHANE is best if used within 12 months from manufacture (refer to batch number on label), when stored in unopened containers under normal conditions of temperature (between 5ºC and 30ºC – DO NOT FREEZE) and humidity. Keep containers closed when not in use.

RESPONSIBLE CARE

URETHANE COATINGS are proud of a conservative tradition of responsible care, and therefore regardless that the VOC levels of PURATHANE are low, it is inappropriate to advise PURATHANE (and all other water borne coatings) is non toxic. Accordingly URETHANE COATINGS recommend that personal protective equipment is used when applying this product.

SAFETY DIRECTIONS

For detailed Health and Safety information refer to the PURATHANE MSDS as it is an integral part of using this product.
PURATHANE is classified as Non-Hazardous however URETHANE COATINGS recommend usage of this material must be in well ventilated conditions to minimise inhalation of vapours. If applying in confined conditions wear respirator with filters that conform to AS 1716. Prevent skin contact by wearing appropriate protective clothing. May irritate skin and eyes. Keep containers firmly closed when not in use. In case of spillage absorb into dry sand or dirt then remove from work area and complete disposal in a responsible manner.

FIRST AID

If affected by inhalation of vapour, remove to fresh air. If breathing difficulty persists or occurs later consult a doctor and have MDSD ready. If swallowed, give water or milk to drink and Do Not induce vomiting. Contact a Doctor or Poisons Information Centre Australia 131126. In case of eye contact, ensuring eyelids are held open, flush immediately with water for fifteen minutes. In case of skin contact, remove contaminated clothing and wash skin with soap and water.

URETHANE COATINGS PURATHANE TWO PACK GLOSS is two component water borne polyurethane finish developed to provide your commercial timber and parquetry floors with extremely hardwearing and long lasting protection. The rapid curing of PURATHANE TWO PACK GLOSS achieves optimal hardness up to 50% faster than single pack water borne polyurethane and higher solids provide greater resistance to wear.
Because water is used as the alternative carrier to solvent, URETHANE COATINGS PURATHANE GLOSS emits low VOC’S (volatile organic compounds) and is therefore user and environmentally friendly but retains all the durable and hard wearing benefits of solvent based polyurethane.

PHYSICAL DESCRIPTION

Appearance:   Opaque liquid.
Colour:             Milky white.
PH:                    >7
Specific Gravity @ 25�C: >1.

PREPARATION

General:

1. Check that timber is adequately seasoned as if not, any subsequent cracking warping and shrinkage may compromise adhesion.
2. Ensure the surface is dry and thoroughly clean, removing all dirt, mildew, wax, grease, resin oils, tannins and dust.
3. Nail holes and surface defects should be filled with water based putty.

New Floors:

Follow steps 1 to 3 above, sand the floor and fine sand, finishing with 120 grit screen back or pad and vacuum thoroughly.

Old Floors:

Follow steps 2 to 3 above and clean with hot water and detergent. Roughen surface completely with 100 grit sandpaper and fine sand finishing, with 120 grit screen back or pad and vacuum thoroughly.
If there is risk of contamination, test for compatibility by applying PURATHANE TWO PACK on a small section of floor first. If ‘craters’ or ‘fisheyes’ appear add 20mls of URETHANE COATINGS PURAMAX Anti Rejection Fluid per Litre of PURATHANE TWO PACK and refer to URETHANE COATINGS PURAMAX directions.

MIXING

Shake each container for one minute and allow each to stand for two minutes, then Mix PURATHANE PART B (BASE) and PURATHANE PART A (HARDENER) at a ratio of 10 to 1 and thoroughly stir, then allow the mixture to stand for two minutes. Always add PURATHANE PART A (HARDENER) to PURATHANE PART B (BASE). Mixed PURATHANE TWO PACK has a pot life of 2 hours (@ 25�C and 50% R.H.). Smaller mixtures (< 2 Litres) and increased temperature and/or reduced humidity will reduce pot life.

APPLICATION

URETHANE COATINGS recommend a 3 coat system for most situations; 1st coat PURASEAL, followed by 2nd and 3rd coats of PURATHANE TWO PACK. A 2 coat system will achieve a high performance finish on hardwood when applied at the rate of 8m² per Litre.

Coat PURASEAL with either PURATHANE or PURATHANE TWO PACK.
N.B. (1) PURATHANE GLOSS, SATIN and MATT are completely compatible with each other, and can be mixed together and coated over each other. (2) PURATHANE TWO PACK GLOSS, SATIN and MATT are completely compatible with each other, and also can be mixed together and coated over each other. (3) Do not mix PURASEAL with PURATHANE or PURATHANE TWO PACK.

As an alternative to PURASEAL, URETHANE COATINGS solvent based TIMBERSEAL is a well proven fast drying sealer. As a 3 coat system TIMBERSEAL can be coated with PURATHANE or PURATHANE TWO PACK.

Application Orientation:

UV Stable, ideal for internal use, verandas, and covered patios.

Application Method: 3 Coat System

1st Coat. Decant PURASEAL directly from the container. Cut in edges with a paint edger or brush, taking care not to proceed excessively ahead of the main coating (particularly in hot and/or dry conditions). Apply PURASEAL at the rate of 10m² per Litre with a 10mm nap waterbased type roller cover or a waterbased applicator, disperse into a uniform finish taking care not to ‘overwork the coating’ allowing it to self level, and wherever possible, finish parallel with the grain. Allow 1.5 to 2 hours to dry (@ 25ºC and 50% R.H.) and prepare to recoat. Do not return unused material to the container.
It is not necessary to fine sand or buff PURASEAL unless surface imperfections or raised grain exist – if so allow 3 hours to dry and then buff with 150 grit screen back (or finer), taking extreme care not to cut through the PURASEAL as this will allow the next coat to ‘wet’ the timber which may then dry a slightly different colour.

2nd Coat. After mixing PURATHANE TWO PACK, cut in edges with a paint edger or brush, taking care not to proceed excessively ahead of the main coating (particularly in hot and/or dry conditions). Apply PURATHANE TWO PACK at the rate of 10m² per Litre with a 10mm nap waterbased type roller cover or a waterbased applicator, disperse into a uniform finish taking care not to ‘overwork the coating’ allowing it to self level, and finish wherever possible parallel with the grain. Allow 2 hours 30 minutes to dry (@ 25ºC and 50% R.H.) and buff with 150 grit screen back, vacuum thoroughly and prepare to recoat. Do not return unused material to the container.

3rd Coat. Repeat directions as detailed under 2nd Coat, finishing parallel with the grain. Allow 8 hours to dry (@ 25ºC and 50% R.H.) before providing access for light foot traffic.

Application Conditions:

Do not apply PURATHANE TWO PACK when ambient/surface temperature is below 10ºC or above 30ºC.
Do not apply PURATHANE TWO PACK if relative humidity is in excess of 85%.
Do not apply PURATHANE TWO PACK if the moisture content of timber is in excess of 14%.

Sanding:

PURATHANE TWO PACK is suitable for sanding after 2 hours 30 minutes drying
(@ 25ºC and 50% R.H.). A good indication that PURTHANE TWO PACK is sufficiently dry is when light sanding using a 150 grit screen back or buffing pad, produces a fine white powder.

USE and MAINTENANCE of a 3 COAT SYSTEM

PURATHANE TWO PACK GLOSS requires 1.5-2 days (@ 25ºC and 50% R.H.) to cure before regular use, and 4 days before using cleaning formulations. Avoid heavy traffic during this period. After the curing period sweep regularly with a soft bristle broom, and if preferred rugs/mats/carpet squares can be placed on the floor. To clean your floor, mix up to one cup Methylated Spirit into a bucket of hot water, and mop the floor regularly rinsing the mop. Use protective pads under legs of furniture. Dirt and grit are abrasive when on the soles of shoes, and can damage any coating. Accordingly mats placed at entrances can assist in removal of grit, reducing abrasion and protecting the coating.

DRYING TIME

Touch dry: 40 minutes. Through Dry: 2 hours. Sanding & Recoat: 2 hours 30 minutes (Without sanding recoat in 90 to 120 minutes). All drying times are @ 25�C and 50% relative humidity. Reduced temperature and/or increased humidity can delay drying time.

COVERAGE

10m² per Litre.

THINNING

URETHANE COATINGS PURATHANE TWO PACK does not require thinning. In hot and/or dry conditions and very large areas where it is difficult to maintain a wet edge, add 50ml of URETHANE COATINGS PURAMATE Wet Edge Extender per Litre of PURATHANE TWO PACK and refer to URETHANE COATINGS PURAMATE directions.

CLEAN UP

Thoroughly wash brush, roller, applicator and equipment with water. If PURATHANE TWO PACK is allowed to ‘become tacky’ on equipment, first rinse off excess with water, then wash off any build up of PURATHANE TWO PACK with URETHANE COATINGS CLEANING SOLVENT or Methylated Spirit, then rinse with water. Dry all equipment before reusing.

PACKAGING

URETHANE COATINGS PURATHANE PART B (BASE) is available in 5 and 10 Litre plastic bottles and PURATHANE PART A (HARDENER) is available in 500ml plastic bottles.

SHELF LIFE

URETHANE COATINGS PURATHANE TWO PACK is best if used within 12 months from manufacture (refer to batch number on label), when stored in unopened containers under normal conditions of temperature (between 5ºC and 30ºC – DO NOT FREEZE) and humidity. Keep containers closed when not in use.

RESPONSIBLE CARE

URETHANE COATINGS are proud of a conservative tradition of responsible care, and therefore regardless that the VOC levels of PURATHANE TWO PACK are low, it is inappropriate to advise PURATHANE TWO PACK (and all other water borne coatings) is non toxic. Accordingly URETHANE COATINGS recommend that personal protective equipment is used when applying this product.

SAFETY DIRECTIONS

For detailed Health and Safety information refer to the PURATHANE TWO PACK MSDS as it is an integral part of using this product.
PURATHANE TWO PACK is classified as Non-Hazardous however URETHANE COATINGS recommend usage of this material must be in well ventilated conditions to minimise inhalation of vapours. If applying in confined conditions wear respirator with filters that conform to AS 1716. Prevent skin contact by wearing appropriate protective clothing. May irritate skin and eyes. Keep containers firmly closed when not in use. In case of spillage absorb into dry sand or dirt then remove from work area and complete disposal in a responsible manner.

FIRST AID

If affected by inhalation of vapour, remove to fresh air. If breathing difficulty persists or occurs later consult a doctor and have MSDS ready. If swallowed, give water or milk to drink and Do Not induce vomiting. Contact a Doctor or Poisons Information Centre Australia 131126. In case of eye contact, ensuring eyelids are held open, flush immediately with water for fifteen minutes. In case of skin contact, remove contaminated clothing and wash skin with soap and water.

URETHANE COATINGS PURATHANE TWO PACK MATT is a two component water borne polyurethane finish developed to provide your commercial timber and parquetry floors with extremely hard wearing and long lasting protection. . The rapid curing of PURATHANE TWO PACK MATT achieves optimal hardness up to 50% faster than single pack water borne polyurethane and higher solids provide greater resistance to wear.
Because water is used as the alternative carrier to solvent, URETHANE COATINGS PURATHANE MATT emits low VOC’S (volatile organic compounds) and is therefore user and environmentally friendly but retains all the durable and hard wearing benefits of solvent based polyurethane.

PHYSICAL DESCRIPTION

Appearance:   Opaque liquid.
Colour:             Milky white.
PH:                    >7
Specific Gravity @ 25�C: >1.

PREPARATION

General:

1. Check that timber is adequately seasoned as if not, any subsequent cracking warping and shrinkage may compromise adhesion.
2. Ensure the surface is dry and thoroughly clean, removing all dirt, mildew, wax, grease, resin oils, tannins and dust.
3. Nail holes and surface defects should be filled with water based putty.

New Floors:

Follow steps 1 to 3 above, sand the floor and fine sand, finishing with 120 grit screen back or pad and vacuum thoroughly.

Old Floors:

Follow steps 2 to 3 above and clean with hot water and detergent. Roughen surface completely with 100 grit sandpaper and fine sand finishing, with 120 grit screen back or pad and vacuum thoroughly.
If there is risk of contamination, test for compatibility by applying PURATHANE TWO PACK on a small section of floor first. If ‘craters’ or ‘fisheyes’ appear add 20mls of URETHANE COATINGS PURAMAX Anti Rejection Fluid per Litre of PURATHANE TWO PACK and refer to URETHANE COATINGS PURAMAX directions.

MIXING

Shake each container for one minute and allow each to stand for two minutes, then Mix PURATHANE PART B (BASE) and PURATHANE PART A (HARDENER) at a ratio of 10 to 1 and thoroughly stir, then allow the mixture to stand for two minutes. Always add PURATHANE PART A (HARDENER) to PURATHANE PART B (BASE). Mixed PURATHANE TWO PACK has a pot life of 2 hours (@ 25�C and 50% R.H.). Smaller mixtures (< 2 Litres) and increased temperature and/or reduced humidity will reduce pot life.

APPLICATION

URETHANE COATINGS recommend a 3 coat system for most situations; 1st coat PURASEAL, followed by 2nd and 3rd coats of PURATHANE TWO PACK. A 2 coat system will achieve a high performance finish on hardwood when applied at the rate of 8m² per Litre.

Coat PURASEAL with either PURATHANE or PURATHANE TWO PACK.
N.B. (1) PURATHANE GLOSS, SATIN and MATT are completely compatible with each other, and can be mixed together and coated over each other. (2) PURATHANE TWO PACK GLOSS, SATIN and MATT are completely compatible with each other, and also can be mixed together and coated over each other. (3) Do not mix PURASEAL with PURATHANE or PURATHANE TWO PACK.

As an alternative to PURASEAL, URETHANE COATINGS solvent based TIMBERSEAL is a well proven fast drying sealer. As a 3 coat system TIMBERSEAL can be coated with PURATHANE or PURATHANE TWO PACK.

Application Orientation:

UV Stable, ideal for internal use, verandas, and covered patios.

Application Method: 3 Coat System

1st Coat. Decant PURASEAL directly from the container. Cut in edges with a paint edger or brush, taking care not to proceed excessively ahead of the main coating (particularly in hot and/or dry conditions). Apply PURASEAL at the rate of 10m² per Litre with a 10mm nap waterbased type roller cover or a waterbased applicator, disperse into a uniform finish taking care not to ‘overwork the coating’ allowing it to self level, and wherever possible, finish parallel with the grain. Allow 1.5 to 2 hours to dry (@ 25ºC and 50% R.H.) and prepare to recoat. Do not return unused material to the container.
It is not necessary to fine sand or buff PURASEAL unless surface imperfections or raised grain exist – if so allow 3 hours to dry and then buff with 150 grit screen back (or finer), taking extreme care not to cut through the PURASEAL as this will allow the next coat to ‘wet’ the timber which may then dry a slightly different colour.

2nd Coat. After mixing PURATHANE TWO PACK, cut in edges with a paint edger or brush, taking care not to proceed excessively ahead of the main coating (particularly in hot and/or dry conditions). Apply PURATHANE TWO PACK at the rate of 10m² per Litre with a 10mm nap waterbased type roller cover or a waterbased applicator, disperse into a uniform finish taking care not to ‘overwork the coating’ allowing it to self level, and finish wherever possible parallel with the grain. Allow 2 hours 30 minutes to dry (@ 25ºC and 50% R.H.) and buff with 150 grit screen back, vacuum thoroughly and prepare to recoat. Do not return unused material to the container.

3rd Coat. Repeat directions as detailed under 2nd Coat, finishing parallel with the grain. Allow 8 hours to dry (@ 25ºC and 50% R.H.) before providing access for light foot traffic.

Application Conditions:

Do not apply PURATHANE TWO PACK when ambient/surface temperature is below 10ºC or above 30ºC.
Do not apply PURATHANE TWO PACK if relative humidity is in excess of 85%.
Do not apply PURATHANE TWO PACK if the moisture content of timber is in excess of 14%.

Sanding:

PURATHANE TWO PACK is suitable for sanding after 2 hours 30 minutes drying
(@ 25ºC and 50% R.H.). A good indication that PURTHANE TWO PACK is sufficiently dry is when light sanding using a 150 grit screen back or buffing pad, produces a fine white powder.

USE and MAINTENANCE of a 3 COAT SYSTEM

PURATHANE TWO PACK GLOSS requires 1.5-2 days (@ 25ºC and 50% R.H.) to cure before regular use, and 4 days before using cleaning formulations. Avoid heavy traffic during this period. After the curing period sweep regularly with a soft bristle broom, and if preferred rugs/mats/carpet squares can be placed on the floor. To clean your floor, mix up to one cup Methylated Spirit into a bucket of hot water, and mop the floor regularly rinsing the mop. Use protective pads under legs of furniture. Dirt and grit are abrasive when on the soles of shoes, and can damage any coating. Accordingly mats placed at entrances can assist in removal of grit, reducing abrasion and protecting the coating.

DRYING TIME

Touch dry: 40 minutes. Through Dry: 2 hours. Sanding & Recoat: 2 hours 30 minutes (Without sanding recoat in 90 to 120 minutes). All drying times are @ 25�C and 50% relative humidity. Reduced temperature and/or increased humidity can delay drying time.

COVERAGE

10m² per Litre.

THINNING

URETHANE COATINGS PURATHANE TWO PACK does not require thinning. In hot and/or dry conditions and very large areas where it is difficult to maintain a wet edge, add 50ml of URETHANE COATINGS PURAMATE Wet Edge Extender per Litre of PURATHANE TWO PACK and refer to URETHANE COATINGS PURAMATE directions.

CLEAN UP

Thoroughly wash brush, roller, applicator and equipment with water. If PURATHANE TWO PACK is allowed to ‘become tacky’ on equipment, first rinse off excess with water, then wash off any build up of PURATHANE TWO PACK with URETHANE COATINGS CLEANING SOLVENT or Methylated Spirit, then rinse with water. Dry all equipment before reusing.

PACKAGING

URETHANE COATINGS PURATHANE PART B (BASE) is available in 5 and 10 Litre plastic bottles and PURATHANE PART A (HARDENER) is available in 500ml plastic bottles.

SHELF LIFE

URETHANE COATINGS PURATHANE TWO PACK is best if used within 12 months from manufacture (refer to batch number on label), when stored in unopened containers under normal conditions of temperature (between 5ºC and 30ºC – DO NOT FREEZE) and humidity. Keep containers closed when not in use.

RESPONSIBLE CARE

URETHANE COATINGS are proud of a conservative tradition of responsible care, and therefore regardless that the VOC levels of PURATHANE TWO PACK are low, it is inappropriate to advise PURATHANE TWO PACK (and all other water borne coatings) is non toxic. Accordingly URETHANE COATINGS recommend that personal protective equipment is used when applying this product.

SAFETY DIRECTIONS

For detailed Health and Safety information refer to the PURATHANE TWO PACK MSDS as it is an integral part of using this product.
PURATHANE TWO PACK is classified as Non-Hazardous however URETHANE COATINGS recommend usage of this material must be in well ventilated conditions to minimise inhalation of vapours. If applying in confined conditions wear respirator with filters that conform to AS 1716. Prevent skin contact by wearing appropriate protective clothing. May irritate skin and eyes. Keep containers firmly closed when not in use. In case of spillage absorb into dry sand or dirt then remove from work area and complete disposal in a responsible manner.

FIRST AID

If affected by inhalation of vapour, remove to fresh air. If breathing difficulty persists or occurs later consult a doctor and have MSDS ready. If swallowed, give water or milk to drink and Do Not induce vomiting. Contact a Doctor or Poisons Information Centre Australia 131126. In case of eye contact, ensuring eyelids are held open, flush immediately with water for fifteen minutes. In case of skin contact, remove contaminated clothing and wash skin with soap and water.

URETHANE COATINGS PURATHANE TWO PACK SATIN is a two component water borne polyurethane finish developed to provide your commercial timber and parquetry floors with extremely hard wearing and long lasting protection. . The rapid curing of PURATHANE TWO PACK SATIN achieves optimal hardness up to 50% faster than single pack water borne polyurethane and higher solids provide greater resistance to wear.
Because water is used as the alternative carrier to solvent, URETHANE COATINGS PURATHANE SATIN emits low VOC’S (volatile organic compounds) and is therefore user and environmentally friendly but retains all the durable and hard wearing benefits of solvent based polyurethane.

PHYSICAL DESCRIPTION

Appearance:   Opaque liquid.
Colour:             Milky white.
PH:                    >7
Specific Gravity @ 25�C: >1.

PREPARATION

General:

1. Check that timber is adequately seasoned as if not, any subsequent cracking warping and shrinkage may compromise adhesion.
2. Ensure the surface is dry and thoroughly clean, removing all dirt, mildew, wax, grease, resin oils, tannins and dust.
3. Nail holes and surface defects should be filled with water based putty.

New Floors:

Follow steps 1 to 3 above, sand the floor and fine sand, finishing with 120 grit screen back or pad and vacuum thoroughly.

Old Floors:

Follow steps 2 to 3 above and clean with hot water and detergent. Roughen surface completely with 100 grit sandpaper and fine sand finishing, with 120 grit screen back or pad and vacuum thoroughly.
If there is risk of contamination, test for compatibility by applying PURATHANE TWO PACK on a small section of floor first. If ‘craters’ or ‘fisheyes’ appear add 20mls of URETHANE COATINGS PURAMAX Anti Rejection Fluid per Litre of PURATHANE TWO PACK and refer to URETHANE COATINGS PURAMAX directions.

MIXING

Shake each container for one minute and allow each to stand for two minutes, then Mix PURATHANE PART B (BASE) and PURATHANE PART A (HARDENER) at a ratio of 10 to 1 and thoroughly stir, then allow the mixture to stand for two minutes. Always add PURATHANE PART A (HARDENER) to PURATHANE PART B (BASE). Mixed PURATHANE TWO PACK has a pot life of 2 hours (@ 25�C and 50% R.H.). Smaller mixtures (< 2 Litres) and increased temperature and/or reduced humidity will reduce pot life.

APPLICATION

URETHANE COATINGS recommend a 3 coat system for most situations; 1st coat PURASEAL, followed by 2nd and 3rd coats of PURATHANE TWO PACK. A 2 coat system will achieve a high performance finish on hardwood when applied at the rate of 8m² per Litre.

Coat PURASEAL with either PURATHANE or PURATHANE TWO PACK.
N.B. (1) PURATHANE GLOSS, SATIN and MATT are completely compatible with each other, and can be mixed together and coated over each other. (2) PURATHANE TWO PACK GLOSS, SATIN and MATT are completely compatible with each other, and also can be mixed together and coated over each other. (3) Do not mix PURASEAL with PURATHANE or PURATHANE TWO PACK.

As an alternative to PURASEAL, URETHANE COATINGS solvent based TIMBERSEAL is a well proven fast drying sealer. As a 3 coat system TIMBERSEAL can be coated with PURATHANE or PURATHANE TWO PACK.

Application Orientation:

UV Stable, ideal for internal use, verandas, and covered patios.

Application Method: 3 Coat System

1st Coat. Decant PURASEAL directly from the container. Cut in edges with a paint edger or brush, taking care not to proceed excessively ahead of the main coating (particularly in hot and/or dry conditions). Apply PURASEAL at the rate of 10m² per Litre with a 10mm nap waterbased type roller cover or a waterbased applicator, disperse into a uniform finish taking care not to ‘overwork the coating’ allowing it to self level, and wherever possible, finish parallel with the grain. Allow 1.5 to 2 hours to dry (@ 25ºC and 50% R.H.) and prepare to recoat. Do not return unused material to the container.
It is not necessary to fine sand or buff PURASEAL unless surface imperfections or raised grain exist – if so allow 3 hours to dry and then buff with 150 grit screen back (or finer), taking extreme care not to cut through the PURASEAL as this will allow the next coat to ‘wet’ the timber which may then dry a slightly different colour.

2nd Coat. After mixing PURATHANE TWO PACK, cut in edges with a paint edger or brush, taking care not to proceed excessively ahead of the main coating (particularly in hot and/or dry conditions). Apply PURATHANE TWO PACK at the rate of 10m² per Litre with a 10mm nap waterbased type roller cover or a waterbased applicator, disperse into a uniform finish taking care not to ‘overwork the coating’ allowing it to self level, and finish wherever possible parallel with the grain. Allow 2 hours 30 minutes to dry (@ 25ºC and 50% R.H.) and buff with 150 grit screen back, vacuum thoroughly and prepare to recoat. Do not return unused material to the container.

3rd Coat. Repeat directions as detailed under 2nd Coat, finishing parallel with the grain. Allow 8 hours to dry (@ 25ºC and 50% R.H.) before providing access for light foot traffic.

Application Conditions:

Do not apply PURATHANE TWO PACK when ambient/surface temperature is below 10ºC or above 30ºC.
Do not apply PURATHANE TWO PACK if relative humidity is in excess of 85%.
Do not apply PURATHANE TWO PACK if the moisture content of timber is in excess of 14%.

Sanding:

PURATHANE TWO PACK is suitable for sanding after 2 hours 30 minutes drying
(@ 25ºC and 50% R.H.). A good indication that PURTHANE TWO PACK is sufficiently dry is when light sanding using a 150 grit screen back or buffing pad, produces a fine white powder.

USE and MAINTENANCE of a 3 COAT SYSTEM

PURATHANE TWO PACK GLOSS requires 1.5-2 days (@ 25ºC and 50% R.H.) to cure before regular use, and 4 days before using cleaning formulations. Avoid heavy traffic during this period. After the curing period sweep regularly with a soft bristle broom, and if preferred rugs/mats/carpet squares can be placed on the floor. To clean your floor, mix up to one cup Methylated Spirit into a bucket of hot water, and mop the floor regularly rinsing the mop. Use protective pads under legs of furniture. Dirt and grit are abrasive when on the soles of shoes, and can damage any coating. Accordingly mats placed at entrances can assist in removal of grit, reducing abrasion and protecting the coating.

DRYING TIME

Touch dry: 40 minutes. Through Dry: 2 hours. Sanding & Recoat: 2 hours 30 minutes (Without sanding recoat in 90 to 120 minutes). All drying times are @ 25�C and 50% relative humidity. Reduced temperature and/or increased humidity can delay drying time.

COVERAGE

10m² per Litre.

THINNING

URETHANE COATINGS PURATHANE TWO PACK does not require thinning. In hot and/or dry conditions and very large areas where it is difficult to maintain a wet edge, add 50ml of URETHANE COATINGS PURAMATE Wet Edge Extender per Litre of PURATHANE TWO PACK and refer to URETHANE COATINGS PURAMATE directions.

CLEAN UP

Thoroughly wash brush, roller, applicator and equipment with water. If PURATHANE TWO PACK is allowed to ‘become tacky’ on equipment, first rinse off excess with water, then wash off any build up of PURATHANE TWO PACK with URETHANE COATINGS CLEANING SOLVENT or Methylated Spirit, then rinse with water. Dry all equipment before reusing.

PACKAGING

URETHANE COATINGS PURATHANE PART B (BASE) is available in 5 and 10 Litre plastic bottles and PURATHANE PART A (HARDENER) is available in 500ml plastic bottles.

SHELF LIFE

URETHANE COATINGS PURATHANE TWO PACK is best if used within 12 months from manufacture (refer to batch number on label), when stored in unopened containers under normal conditions of temperature (between 5ºC and 30ºC – DO NOT FREEZE) and humidity. Keep containers closed when not in use.

RESPONSIBLE CARE

URETHANE COATINGS are proud of a conservative tradition of responsible care, and therefore regardless that the VOC levels of PURATHANE TWO PACK are low, it is inappropriate to advise PURATHANE TWO PACK (and all other water borne coatings) is non toxic. Accordingly URETHANE COATINGS recommend that personal protective equipment is used when applying this product.

SAFETY DIRECTIONS

For detailed Health and Safety information refer to the PURATHANE TWO PACK MSDS as it is an integral part of using this product.
PURATHANE TWO PACK is classified as Non-Hazardous however URETHANE COATINGS recommend usage of this material must be in well ventilated conditions to minimise inhalation of vapours. If applying in confined conditions wear respirator with filters that conform to AS 1716. Prevent skin contact by wearing appropriate protective clothing. May irritate skin and eyes. Keep containers firmly closed when not in use. In case of spillage absorb into dry sand or dirt then remove from work area and complete disposal in a responsible manner.

FIRST AID

If affected by inhalation of vapour, remove to fresh air. If breathing difficulty persists or occurs later consult a doctor and have MSDS ready. If swallowed, give water or milk to drink and Do Not induce vomiting. Contact a Doctor or Poisons Information Centre Australia 131126. In case of eye contact, ensuring eyelids are held open, flush immediately with water for fifteen minutes. In case of skin contact, remove contaminated clothing and wash skin with soap and water.

URETHANE COATINGS PURATHANE TWO PACK is two component water borne polyurethane finish developed to provide your commercial timber and parquetry floors with extremely hardwearing and long lasting protection. The rapid curing of PURATHANE TWO PACK achieves optimal hardness up to 50% faster than single pack water borne polyurethane and higher solids provide greater resistance to wear.
Because water is used as the alternative carrier to solvent, URETHANE COATINGS PURATHANE TWO PACK emits low VOC’S (volatile organic compounds) and is therefore user and environmentally friendly but retains all the durable and hard wearing benefits of solvent based polyurethane.

 

PHYSICAL DESCRIPTION

Appearance:    Opaque liquid.
Colour:               Milky white.
PH:                       >7
Specific Gravity @ 25ºC: >1.

PREPARATION

Please refer to PREPARATION directions detailed on PURATHANE PART B (BASE) Technical Data Sheet or Label.

MIXING

Shake each container for one minute and allow each to stand for two minutes, then Mix PURATHANE PART B (BASE) and PURATHANE PART A (HARDENER) at a ratio of 10 to 1 and thoroughly stir, then allow the mixture to stand for two minutes. Always add PURATHANE PART A (HARDENER) to PURATHANE PART B (BASE). Mixed PURATHANE TWO PACK has a pot life of 2 hours (@ 25ºC and 50% R.H.). Smaller mixtures (< 2 Litres) and increased temperature and/or reduced humidity will reduce pot life.

APPLICATION

Please refer to APPLICATION directions detailed on PURATHANE PART B (BASE) Label.

DRYING TIME

Touch dry: 40 minutes. Through Dry: 2 hours. Sanding & Recoat: 2 hours 30 minutes (Without sanding recoat in 90 to 120 minutes). All drying times are @ 25ºC and 50% relative humidity. Reduced temperature and/or increased humidity can delay drying time.

COVERAGE

10m² per Litre.

THINNING

URETHANE COATINGS PURATHANE TWO PACK does not require thinning. In hot and/or dry conditions and very large areas where it is difficult to maintain a wet edge, add 50ml of URETHANE COATINGS PURAMATE Wet Edge Extender per Litre of PURATHANE TWO PACK and refer to URETHANE COATINGS PURAMATE directions.

CLEAN UP

Thoroughly wash brush, roller, applicator and equipment with water. If PURATHANE TWO PACK is allowed to ‘become tacky’ on equipment, first rinse off excess with water, then wash off any build up of PURATHANE TWO PACK with URETHANE COATINGS CLEANING SOLVENT or Methylated Spirit, then rinse with water. Dry all equipment before reusing.

PACKAGING

URETHANE COATINGS PURATHANE PART B (BASE) is available in 5 and 10 Litre plastic bottles and PURATHANE PART A (HARDENER) is available in 500ml plastic bottles.

SHELF LIFE

URETHANE COATINGS PURATHANE TWO PACK is best if used within 12 months from manufacture (refer to batch number on label), when stored in unopened containers under normal conditions of temperature (between 5ºC and 30ºC – DO NOT FREEZE) and humidity. Keep containers closed when not in use.

RESPONSIBLE CARE

URETHANE COATINGS are proud of a conservative tradition of responsible care, and therefore regardless that the VOC levels of PURATHANE TWO PACK are low, it is inappropriate to advise PURATHANE TWO PACK (and all other water borne coatings) is non toxic. Accordingly URETHANE COATINGS recommend that personal protective equipment is used when applying this product.

SAFETY DIRECTIONS

For detailed Health and Safety information refer to the PURATHANE TWO PACK MSDS as it is an integral part of using this product.
PURATHANE TWO PACK is classified as Non-Hazardous however URETHANE COATINGS recommend usage of this material must be in well ventilated conditions to minimise inhalation of vapours. If applying in confined conditions wear respirator with filters that conform to AS 1716. Prevent skin contact by wearing appropriate protective clothing. May irritate skin and eyes. Keep containers firmly closed when not in use. In case of spillage absorb into dry sand or dirt then remove from work area and complete disposal in a responsible manner.

FIRST AID

If affected by inhalation of vapour, remove to fresh air. If breathing difficulty persists or occurs later consult a doctor and have MSDS ready. If swallowed, give water or milk to drink and Do Not induce vomiting. Contact a Doctor or Poisons Information Centre Australia 131126. In case of eye contact, ensuring eyelids are held open, flush immediately with water for fifteen minutes. In case of skin contact, remove contaminated clothing and wash skin wash with soap and water.