MODIFIED OIL - GLOSS
A resin modified Oil, providing improved durability over alternative oil finishes, suitable for interior coating of all timber species. Ideal for coating New Timber Floors suspected of being prone to shrinkage. Especially suitable for clients concerned of fumes from Polyurethane as only low VOC white spirits is used as the solvent. Gloss finish.
USES:
- Ideal for coating NEW TIMBER FLOORS suspected of being prone to shrinkage. MODIFIED OIL GLOSS will greatly reduce the occurrence of EDGE BONDING.
- For clients concerned about exposure to fumes from POLYURETHANES, MODIFIED OIL GLOSS is less likely to cause discomfort because only low VOC WHITE SPIRIT is used as the solvent.
- MODIFIED OIL GLOSS is completely compatible with URETHANE COATINGS MODIFIED OIL SATIN and/or TUNGSEAL.
APPLICATION:
- Fine sand timber to a smooth finish. Hardwoods must not be burnished and grain must remain open. Accordingly, Urethane Coatings recommend nothing finer than 120 grit paper or equivalent is used to finish sanding new hardwood floors or to finish sanding old hardwood floors back to bare timber. Vacuum thoroughly. Ensure the timber surface if free from dust, wax or oily substances.
- SHAKE WELL and/or STIR THOROUGHLY
- The first coat may be either (a) Urethane Coatings TUNGSEAL PENETRATING FIRST COAT or (b) Urethane Coatings TIMBER SEAL. Apply with a mohair roller, lambswool applicator or brush
- Allow 30 to 60 minutes to dry, then lightly sand with a worn 150 mesh screenback and vacuum thoroughly. If two coats of MODIFIED OIL are to be applied, sanding of the first TUNGSEAL Penetrating Coat or TIMBERSEAL is unnecessary.
- Apply the second coat – MODIFIED OIL GLOSS – with a mohair roller, lambswool applicator or brush.
- Allow to dry overnight, lightly sand with a worn 150 mesh screenback. NOTE; If the coating does not sand to a fine white powder, leave for another 24 hours. Some timber species exude oils and antioxidants which severely retard the curing process.
- Apply a final coat of MODIFIED OIL GLOSS.
- Do not return unused material to the can.
- Thoroughly clean the mohair roller, lamb’s wool applicator or brush in URETHANE COATINGS MINERAL TURPENTINE. Dry all equipment before reusing.
SHELF LIFE:
This product is best if used within 12 months from manufacture (refer to batch number), when stored in unopened containers under normal conditions of temperature and humidity.
COVERAGE:
10-12m² per litre.
IMPORTANT NOTICE:
MODIFIED OIL GLOSS is prone to ‘skinning’, therefore if applying a partly used drum, it may be necessary to strain the MODIFIED OIL GLOSS through a stocking.
MAINTENANCE:
MODIFIED OIL GLOSS has wearing properties at least equivalent to all other oil based floor coatings. However, in most situations a sacrificial wear surface, i.e. a polish is required to take the brunt of the traffic. Suitable polishes are: Johnsons One Go, Reckitts Long Life, or Peerless Gemini. All these are water based and easily applied with a foam applicator. Polish should be applied after allowing at least seven to ten days for the MODIFIED OIL GLOSS to cure, avoid heavy traffic during this period. Use protective pads under legs of furniture.
Regularly wipe over the floor with an antistatic mop or sweep with a soft bristle broom. We caution against the use of vacuum cleaners, particularly if the bristles are worn as the cleaning head may then scratch the floor. The frequency of cleaning is dependent on the level of traffic, amount of grit carried onto the floor, and activity of children, and pets etc.
To clean your floor, mix up to one cup of Methylated Spirits into a bucket of hot water, and mop the floor, regularly rinsing the mop. If the floor is particularly dirty, wash first with a non abrasive detergent then clean with the Methylated spirits and water solution – this will prevent streaking and smear marks that sometimes remain after use of detergents and/or household cleaners.
RECOATING:
Before recoating all residual polish must be completely removed. Refer to the polish manufacturers recommendations for the correct method of removal. The removal of wax polish is more difficult than water based polishes and requires repeated washes with Mineral Turpentine, or in extreme cases sanding back to bare timber.
SAFETY DIRECTIONS:
Usage of this material must be under well ventilated conditions to minimise inhalation of vapours. Wear respirator with filters that conform with AS1716. Asthmatics, the very young, elderly people and pets should leave the site during the first 24 hours. Prevent skin contact by wearing impervious gloves. Breathing of vapour may be harmful and may cause lung irritation and allergic respiratory reaction. May irritate skin and eyes. Keep container firmly lidded, as this product will skin and slowly cure when exposed to air. In case of spillage, absorb into dry sand or dirt. Remove from work area and cover with water for 24 hours prior to disposal.
WARNING FLAMMABLE:
Contains 80gms per litre of Aromatic Hydrocarbons. This drum contains volatile and flammable solvents and when using contents adequate ventilation to the outside must be provided. All potential sources of ignition (open flames, pilot lights, furnaces, spark producing electrical switches, etc.) must be eliminated in or near the working area. DO NOT SMOKE. Keep drum closed when not in use.
FIRST AID:
If affected by inhalation of vapour, remove to fresh air. If breathing difficulty persists or occurs later, consult a doctor and have label ready. If swallowed, do NOT induce vomiting. Give water or milk.
CONTACT DOCTOR OR POISONS INFORMATION CENTRE Australia 131126.
In case of eye contact, flush immediately with water for fifteen minutes and call a doctor. In case of skin contact, remove contaminated clothing and wash skin first with Methylated spirit, then with soap and water.
MODIFIED OIL - MATT
Click on SDS and TDS for more information
MODIFIED OIL - SATIN
A resin modified Oil, providing improved durability over alternative oil finishes, suitable for interior coating of all timber species. Ideal for coating New Timber Floors suspected of being prone to shrinkage. Especially suitable for clients concerned of fumes from Polyurethane as only low VOC white spirits is used as the solvent. Satin finish.
USES:
- Ideal for coating NEW TIMBER FLOORS suspected of being prone to shrinkage. MODIFIED OIL SATIN will greatly reduce the occurrence of EDGE BONDING.
- For clients concerned about exposure to fumes from POLYURETHANES, MODIFIED OIL SATIN is less likely to cause discomfort because only low VOC WHITE SPIRIT is used as the solvent.
- MODIFIED OIL SATIN is not as subject to SHEEN VARIATION as LOW SHEEN POLYURETHANES.
- MODIFIED OIL SATIN is completely compatible with URETHANE COATINGS MODIFIED OIL GLOSS and/or TUNGSEAL.
APPLICATION:
- Fine sand timber to a smooth finish. Hardwoods must not be burnished and grain must remain open. Accordingly, Urethane Coatings recommend nothing finer than 120 grit paper or equivalent is used to finish sanding new hardwood floors or to finish sanding old hardwood floors back to bare timber. Vacuum thoroughly. Ensure the timber surface if free from dust, wax or oily substances.
- SHAKE WELL and/or STIR THOROUGHLY
- The first coat may be either (a) Urethane Coatings TUNGSEAL PENETRATING FIRST COAT or (b) Urethane Coatings TIMBER SEAL. Apply with a mohair roller, lambswool applicator or brush
- Allow 30 to 60 minutes to dry, then lightly sand with a worn 150 mesh screenback and vacuum thoroughly. If two coats of MODIFIED OIL are to be applied, sanding of the first TUNGSEAL Penetrating Coat or TIMBERSEAL is unnecessary.
- Apply the second coat – MODIFIED OIL GLOSS or MODIFIED OIL SATIN – with a mohair roller, lambswool applicator or brush.
- Allow to dry overnight, lightly sand with a worn 150 mesh screenback. NOTE; If the coating does not sand to a fine white powder, leave for another 24 hours. Some timber species exude oils and antioxidants which severely retard the curing process.
- Apply a final coat of MODIFIED OIL SATIN.
- Do not return unused material to the can.
- Thoroughly clean the mohair roller, lamb’s wool applicator or brush in URETHANE COATINGS MINERAL TURPENTINE. Dry all equipment before reusing.
SHELF LIFE
This product is best if used within 12 months from manufacture (refer to batch number), when stored in unopened containers under normal conditions of temperature and humidity.
COVERAGE:
10-12m² per litre.
IMPORTANT NOTICE:
MODIFIED OIL SATIN is prone to ‘skinning’, therefore if applying a partly used drum, it may be necessary to strain the MODIFIED OIL SATIN through a stocking.
MAINTENANCE:
MODIFIED OIL SATIN has wearing properties at least equivalent to all other oil based floor coatings. However, in most situations a sacrificial wear surface, i.e. a polish is required to take the brunt of the traffic. Suitable polishes are: Johnsons One Go, Reckitts Long Life, or Peerless Gemini. All these are water based and easily applied with a foam applicator. Polish should be applied after allowing at least seven to ten days for the MODIFIED OIL SATIN to cure, avoid heavy traffic during this period. Use protective pads under legs of furniture.
Regularly wipe over the floor with an antistatic mop or sweep with a soft bristle broom. We caution against the use of vacuum cleaners, particularly if the bristles are worn as the cleaning head may then scratch the floor. The frequency of cleaning is dependent on the level of traffic, amount of grit carried onto the floor, and activity of children, and pets etc.
To clean your floor, mix up to one cup of Methylated Spirits into a bucket of hot water, and mop the floor, regularly rinsing the mop. If the floor is particularly dirty, wash first with a non abrasive detergent then clean with the Methylated spirits and water solution – this will prevent streaking and smear marks that sometimes remain after use of detergents and/or household cleaners.
RECOATING:
Before recoating all residual polish must be completely removed. Refer to the polish manufacturers recommendations for the correct method of removal. The removal of wax polish is more difficult than water based polishes and requires repeated washes with Mineral Turpentine, or in extreme cases sanding back to bare timber.
SAFETY DIRECTIONS:
Usage of this material must be under well ventilated conditions to minimise inhalation of vapours. Wear respirator with filters that conform with AS1716. Asthmatics, the very young, elderly people and pets should leave the site during the first 24 hours. Prevent skin contact by wearing impervious gloves. Breathing of vapour may be harmful and may cause lung irritation and allergic respiratory reaction. May irritate skin and eyes. Keep container firmly lidded, as this product will skin and slowly cure when exposed to air. In case of spillage, absorb into dry sand or dirt. Remove from work area and cover with water for 24 hours prior to disposal.
WARNING FLAMMABLE:
Contains 80gms per litre of Aromatic Hydrocarbons. This drum contains volatile and flammable solvents and when using contents adequate ventilation to the outside must be provided. All potential sources of ignition (open flames, pilot lights, furnaces, spark producing electrical switches, etc.) must be eliminated in or near the working area. DO NOT SMOKE. Keep drum closed when not in use.
FIRST AID:
If affected by inhalation of vapour, remove to fresh air. If breathing difficulty persists or occurs later, consult a doctor and have label ready. If swallowed, do NOT induce vomiting. Give water or milk. CONTACT DOCTOR OR POISONS INFORMATION CENTRE Australia 131126. In case of eye contact, flush immediately with water for fifteen minutes and call a doctor. In case of skin contact, remove contaminated clothing and wash skin first with Methylated spirits, then with soap and water.
NATURAL DECKING OIL
Contains Tung and Linseed oil, formulated to provide long lasting protection for all outdoor timber. Low sheen finish.
USES:
URETHANE COATINGS NATURAL DECKING OIL has been developed to provide long lasting protection for exterior timber structures including, decking, outdoor furniture, unpainted weather boards, door jams, window frames, fences, steps, and railings.
URETHANE COATINGS NATURAL DECKING OIL offers a low sheen, semi-transparent finish highlighting the natural features and grain of timber, protecting and extending the life of timber, and weathers naturally without cracking and pealing.
PREPARATION:
General:
1 Check that timber is adequately seasoned to prevent cracking and warping, then thoroughly clean removing all dirt, mildew, wax, resin oils, and tannins.
2. Nail holes and surface defects should be filled.
3. Apply URETHANE COATINGS NATURAL DECKING OIL within 1 week of surface preparation to retain the natural timber colour as timber weathering can result in loss of timber colour and contribute to reduced durability.
New Bare Timber:
Follow steps 1 to 3 above. If Timber is extremely oily or tannin rich, wash and scrub down with URETHANE COATINGS TIMBER CLEAN and rinse off with water. Lightly sand if necessary.
Previously Coated Timbers (Painted, Oiled or Stained) or Weathered Timber:
Sand paint back to bare timber and follow steps 1 to 3 above. If coated with URETHANE COATINGS NATURAL DECKING OIL, URETHANE COATINGS TIMBER STAINS. Wash and sand, removing all weathered NATURAL DECKING OIL and / or TIMBER STAIN, remove dust, and apply URETHANE COATINGS NATURAL DECKING OIL, following steps 1 to 3 above. Sand weathered timber back to fresh timber and follow steps 1 to 3 above.
APPLICATION:
Stir URETHANE COATINGS NATURAL DECKING OIL thoroughly before and during use. Apply by brush, roller or applicator. Allow the first coat to dry for 8 to 12 hours. Wait minimum one day and, apply the second coat and wipe off any excess oil before becoming tacky (after 20-40 minutes). Allow the second coat a further day to dry if applying a third coat. Use three coats for optimal performance.
COVERAGE:
Softwood: 6-8 m² per litre, Hardwood: 8-10 m² per litre
THINNING:
URETHANE COATINGS NATURAL DECKING OIL does not require thinning.
MAINTENANCE & RECOATING:
As the timber begins to show signs of weathering (dryness, change of colour, or reduced water repellency), recoat with up to two coats of URETHANE COATINGS NATURAL DECKING OIL applying as described under ‘Application’.
CLEAN UP:
Clean brush, roller or applicator and equipment using URETHANE COATINGS MINERAL TURPENTINE, and rinse with hot soapy water.
DRYING TIME:
Touch dry; 3 hours at 25° C and 50% relative humidity. Reduced temperature and/or increased humidity can delay drying time. Allow the first coat to dry for 8 to 12 hours. Wait minimum one day and, apply the second coat. Allow the second coat a further day to dry if applying a third coat. Use three coats for optimal performance. Suitable for light foot traffic 48 hours after final coat. Do not apply in temperatures below 10° C or above 35° C.
SHELF LIFE:
This product is best if used within 12 months from manufacture (refer to batch number), when stored in unopened containers under normal conditions of temperature and humidity.
Contains no more than 0.7 grams per 100mls of volatile free organic isocyanate.
SAFETY DIRECTIONS:
Usage of this material must be under well ventilated conditions to minimise inhalation of vapours. If applying in confined conditions wear respirator with filters that conform to AS 1716. Asthmatics, the very young, elderly people and pets should avoid inhalation of vapours as breathing of vapour may cause lung irritation. Prevent skin contact by wearing impervious gloves. May irritate skin and eyes. Keep container firmly lidded, as this product will skin and slowly cure when exposed to air. In case of spillage, absorb into dry sand or dirt then remove from work area and complete disposal in responsible manner.
WARNING FLAMMABLE:
Contains 105gms per litre of Aromatic Hydrocarbons. This drum contains volatile and flammable solvents therefore when applying the contents provide adequate ventilation. All potential sources of ignition (open flames, pilot lights, furnaces, spark producing electrical switches, etc.) must be eliminated in or near the working area. DO NOT SMOKE. Keep drum closed when not in use
FIRST AID: If affected by inhalation of vapour, remove to fresh air. If breathing difficulty persists or occurs later, consult a doctor and have label ready. If swallowed, do NOT induce vomiting. Give water or milk. CONTACT DOCTOR OR POSIONS INFORMATION CENTRE Australia 131126. In case of eye contact, flush immediately with water for fifteen minutes and call a doctor. In case of skin contact, remove contaminated clothing and wash skin first with Methylated spirits, then soap and water.
TUNGSEAL
A resin modified Tung Oil, suitable for interior coating of all timber species. Ideal for coating New Timber Floors suspected of being prone to shrinkage. Especially suitable for clients concerned of fumes from Polyurethane as only low VOC white spirits is used as the solvent. Semi Gloss finish.
USES:
- Ideal for coating NEW TIMBER FLOORS suspected of being prone to shrinkage. TUNGSEAL will greatly reduce the occurrence of EDGE BONDING.
- For clients concerned about exposure to fumes from POLYURETHANES, TUNGSEAL is less likely to cause discomfort, because only low VOC WHITE SPIRIT is used as the solvent.
- Where a more natural timber look is required, use TUNGSEAL.
- TUNGSEAL is not as subject to SHEEN VARIATION as REDUCED SHEEN POLYURETHANES.
- TUNGSEAL is completely compatible with URETHANE COATINGS MODIFIED OIL GLOSS and/or MODIFIED OIL SATIN.
APPLICATION:
- Fine sand timber to a smooth finish. Hardwoods must not be burnished and grain must remain open. Accordingly, Urethane Coatings recommend nothing finer than 120 grit paper or equivalent is used to finish sanding new hardwood floors or to finish sanding old hardwood floors back to bare timber. Vacuum thoroughly. Ensure the timber surface if free from dust, wax or oily substances.
- SHAKE WELL and/or STIR THOROUGHLY
- The first coat may be either (a) Urethane Coatings TUNGSEAL PENETRATING FIRST COAT or (b) Urethane Coatings TIMBER SEAL. Apply with a mohair roller, lambswool applicator or brush
- Allow 30 to 60 minutes to dry, then lightly sand with a worn 150 mesh screenback and vacuum thoroughly. If two coats of TUNGSEAL are to be applied, sanding of the first TUNGSEAL Penetrating Coat or TIMBERSEAL is unnecessary.
- Apply the second coat – TUNGSEAL – with a mohair roller, lambswool applicator or brush.
- Allow to dry overnight, lightly sand with a worn 150 mesh screenback. NOTE; If the coating does not sand to a fine white powder, leave for another 24 hours. Some timber species exude oils and antioxidants which severely retard the curing process.
- Apply a final coat of TUNGSEAL.
- Do not return unused material to the can.
- Thoroughly clean the mohair roller, lamb’s wool applicator or brush in URETHANE COATINGS MINERAL TURPENTINE. Dry all equipment before reusing.
SHELF LIFE:
This product is best if used within 12 months from manufacture (refer to batch number), when stored in unopened containers under normal conditions of temperature and humidity.
COVERAGE:
10-12m² per litre.
IMPORTANT NOTICE:
TUNGSEAL is prone to ‘skinning’, therefore if applying a partly used drum, it may be necessary to strain the TUNGSEAL through a stocking.
MAINTENANCE:
TUNGSEAL has wearing properties at least equivalent to all other oil based floor coatings. However, in most situations a sacrificial wear surface, i.e. a polish is required to take the brunt of the traffic. Suitable polishes are: Johnsons One Go, Reckitts Long Life, or Peerless Gemini. All these are water based and easily applied with a foam applicator. Polish should be applied after allowing at least seven to ten days for the TUNGSEAL to cure, avoid heavy traffic during this period. Use protective pads under legs of furniture.
Regularly wipe over the floor with an antistatic mop or sweep with a soft bristle broom. We caution against the use of vacuum cleaners, particularly if the bristles are worn as the cleaning head may then scratch the floor. The frequency of cleaning is dependent on the level of traffic, amount of grit carried onto the floor, and activity of children, and pets etc.
To clean your floor, mix up to one cup of Methylated Spirits into a bucket of hot water, and mop the floor, regularly rinsing the mop. If the floor is particularly dirty, wash first with a non abrasive detergent then clean with the Methylated spirits and water solution – this will prevent streaking and smear marks that sometimes remain after use of detergents and/or household cleaners.
RECOATING:
Before recoating all residual polish must be completely removed. Refer to the polish manufacturers recommendations for the correct method of removal. The removal of wax polish is more difficult than water based polishes and requires repeated washes with Mineral Turpentine, or in extreme cases sanding back to bare timber.
SAFETY DIRECTIONS:
Usage of this material must be under well ventilated conditions to minimise inhalation of vapours. Wear respirator with filters that conform with AS1716. Asthmatics, the very young, elderly people and pets should leave the site during the first 24 hours. Prevent skin contact by wearing impervious gloves. Breathing of vapour may be harmful and may cause lung irritation and allergic respiratory reaction. May irritate skin and eyes. Keep container firmly lidded, as this product will skin and slowly cure when exposed to air. In case of spillage, absorb into dry sand or dirt. Remove from work area and cover with water for 24 hours prior to disposal.
WARNING FLAMMABLE:
Contains 75gms per litre of Aromatic Hydrocarbons. This drum contains volatile and flammable solvents and when using contents adequate ventilation to the outside must be provided. All potential sources of ignition (open flames, pilot lights, furnaces, spark producing electrical switches, etc.) must be eliminated in or near the working area. DO NOT SMOKE. Keep drum closed when not in use.
FIRST AID:
If affected by inhalation of vapour, remove to fresh air. If breathing difficulty persists or occurs later, consult a doctor and have label ready. If swallowed, do NOT induce vomiting. Give water or milk.
CONTACT DOCTOR OR POISONS INFORMATION CENTRE Australia 131126.
In case of eye contact, flush immediately with water for fifteen minutes and call a doctor. In case of skin contact, remove contaminated clothing and wash skin first with Methylated spirits, then with soap and water.